压滤机入料泵是专业为压滤机消费的进料、入料的配套用泵，压滤机入料泵是一种性能特殊的压滤机入料泵，前期将来流量大、压力低；后期压榨流量小、压力高；十分合适压滤机所需的入料性能。
压滤机入料泵在装置时必需先压紧电机螺栓、泵螺栓和底角栓，接着检验电机和泵的同轴度，用平板或锯条靠在电泵联上，停止调整，要必需保证平行同轴，而要必需坚持电泵联间隙2-3mm，为以后的调试运用打好根底，否则会在以后的实验和运转中呈现噪音，影响泵的工作效率，严重的会缩短泵的运用寿命。
制止自觉开大出口阀门，以免形成烧坏电机。需啊哟调整排料量时，切记应调整出口阀门，调整进料阀门易形成泵汽蚀，损伤极大。假如泵的进料页面过高（超越20m）或进料压力过大而形成盘根漏料时要恰当押金盘根，到达不漏料为宜，不可压的过紧。
为了防止停泵漏料，停泵前可恰当压紧一点盘根。关闭进口阀门，并马上停泵，以免发作倒压形成泵的反转发作设备损坏和盘根向外漏料。并快速翻开放料阀门，最后渐渐翻开泵的出口阀门，将出料管内的物料放完，为了防止杂质在泵腔内堆积梗塞，必要时要装置冲洗水管停止冲洗。
The filter press feed pump is a supporting pump for feeding and feeding produced for the filter press. The filter press feed pump is a filter press feed pump with special performance, with large flow and low pressure in the early future; In the later stage, the pressing flow is small and the pressure is high; It is very suitable for the feeding performance required by the filter press.
Installation and operation of feed pump of filter press
During the installation of the feed pump of the filter press, the motor bolt, pump bolt and bottom corner bolt must be pressed first, and then the coaxiality of the motor and pump must be checked. Use a flat plate or saw blade to lean against the electric pump coupling for adjustment. The parallel coaxiality must be ensured, and the clearance of the electric pump coupling must be maintained at 2-3mm, so as to lay a foundation for future commissioning, otherwise there will be noise in future experiments and operation, Affect the working efficiency of the pump, and seriously shorten the service life of the pump.
The feed pump of the filter press is started and operated
Close the outlet valve when starting the feed pump of the filter press. After the starting motor operates normally, gradually open the outlet valve and pay attention to the current until it reaches the rated current.
Precautions for use of feed pump of filter press
It is forbidden to open the outlet valve blindly to avoid burning the motor. When adjusting the discharge volume, remember to adjust the outlet valve. Adjusting the feed valve is easy to cause pump cavitation and great damage. If the feeding page of the pump is too high (more than 20m) or the feeding pressure is too large, resulting in packing leakage, appropriate deposit packing shall be made to ensure no material leakage, and it shall not be pressed too tightly.
The feed pump of filter press stops working
In order to avoid material leakage during pump shutdown, a little packing can be properly pressed before pump shutdown. Close the inlet valve and stop the pump immediately to avoid equipment damage and packing leakage caused by reverse pressure. Quickly open the discharge valve, and finally slowly open the outlet valve of the pump to discharge the materials in the discharge pipe. In order to avoid the deposition and blockage of impurities in the pump cavity, install a flushing water pipe for flushing if necessary.
